Loading... Please wait...
Click the image above to see a larger version
  • White balls - Yi - Scarab-Knife - Camera Tilt mount kit - Gello Killer
  • White balls - Yi - Scarab-Knife - Camera Tilt mount kit - Gello Killer
  • The GoPro and Yi camera frames are different sizes - be sure to order the correct one
  • White balls - Yi - Scarab-Knife - Camera Tilt mount kit - Gello Killer
  • White balls - Yi - Scarab-Knife - Camera Tilt mount kit - Gello Killer
  • White balls - Yi - Scarab-Knife - Camera Tilt mount kit - Gello Killer
  • White balls - Yi - Scarab-Knife - Camera Tilt mount kit - Gello Killer
  • White balls - Yi - Scarab-Knife - Camera Tilt mount kit - Gello Killer

White balls - Yi - Scarab-Knife - Camera Tilt mount kit - Gello Killer

$17.50
Shipping Weight:
180.00 Grams

Sorry but this item is currently unavailable.

Please check back at a later stage.

Stock Remaining:
Out of stock


Product Description

Fly your Yi HDCam on your Scarab Knife - White Balls GoPro mount kit - This Yi Scarab Knife camera mount kit is for Scarab Knife and allows a Yi to be flown "tilted back" for fast FPV flying without having issues of the Yi camera facing to far down and no forward vision in your HD recordings - Carrying a Yi is considered to be a large payload and suited to the more powerful CarbonBird 1806 Black or 2206 Race Motors (red 2203 motors are for FPV cam only, lighter setups and not designed to carry the extra weight of the Yi size HD cameras) - The best prop for carrying a Yi is the HQProp6*4.5 on 3s1500 or HQProp 5*4*3 triples on 4S with Black 1806 motors - the Race Spec motors can carry a wide range of props as they are the most powerful motors.

The Kit has been designed with our new extra-stiff white balls to ensure the Yi is held firmly at a tilted back angle without needing a compression band- gello free - We dont recommend zip ties to hold the White balls as in an extreme High "G" crash the forces may be transferred to your Yi - some pilots attach Red ribbons to their Yi to help find them when they detach which is a good idea.

 

Includes

  • Yi Frame mount - black (fits Yi - not suitable for GoPro)
  • 5mm SS Bolt/Nut
  • Yi bracket pivot/nut
  • Anti vibration Gello tray Carbon fibre
  • 4*White Gello Killer Balls - extra stiff

 

Excludes 

  • Excludes Yi camera
  • Excludes Prop and motor balancing, First up
  • Requires assembly and drilling of frame to widen Gello Balls hole - see below
  • Excludes tools - Requires 8mm drill bit ; diamond file ; soapy water ; 3mm hex tool ; 8mm spanner for nut 
  • RISK - Be aware of the risk of flying your Yi camera fast at low level in the event of a crash is your decision - if you crash your Yi may be destroyed - you should insure your Yi for risk with your insurer
  • Cannot by used for GoPro camera which is a few mm different size - that mount kit for GoPro is HERE

 

To Install

  1. Hold the camera plate over the top frame and identify the 4 holes for the White balls ; then
  2. The frames holes for balls are 7mm - if you find it too hard to insert white balls you can dremel/grind them slightly bigger to 8mm - see note*
  3. dull down all 8 holes (top frame 4 and camera plate 4) to remove any sharp edge which might cut your balls
  4. Add soapy water to a bowl and dip the white balls into the soapy mixture to make them slippery
  5. Fold the ball in on itself from the side - then push it into the frame with a twisting motion
  6. Repeat for all 4 balls
  7. Intall the top camera plate onto the 4 balls - again pushing them thru
  8. Charge your Yi first - then install the Yi into the Black Frame
  9. line the 2-fingers of the frame with the 3-fingers of the silver pivot mount
  10. insert and tighten the 5mm bolt and nut - tighten the nut/bolt to achieve a firm fit
  11. When Yi is carried on a Scarab Knife the Main LiPo must be moved to the rear position

NOTE - with patience and soapy water the strong White balls can be inserted in the 7mm holes. Be carefull not to use sharp steel tools to pull or push the gel balls as you may cut/damage them.  If you wish you can slightly widen the holes to 8mm on the frame side - but be sure to use a dremel to grind them bigger - NOT a twist drill as twist drills can act like a screw and rip thru the carbon giving poor result - so a small abrasive/diamond coated bit on the dremel is by far the best way to modify carbon holes. 


Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!




Currency conversion