Loading... Please wait...
Click the image above to see a larger version
  • Image 1
  • Image 2
  • Image 3

Power Distribution board - Voltair - Fully Assembled - 200 Amp 8+3+4 Way

$27.50
Shipping Weight:
215.00 Grams
Rating:
Stock Remaining:
19


Product Description

Designed for the Scarab Hunter Octa - a 200Amp power distribution board for 2 or 4 6S5000 LiPo - typically a 6S 20,000 mah setup - Even if one or 2 battery connectors where to fail the other 2 will still supply power un interupted - 4 way redundant design !

Fully assembled version of VoltAir® 3.5mm is our new XT60 x 8 - a 200 amp power distribution board for 15,000 to 20,000mah Octas ->6S -  a small 50mmx50mm PCB  - which makes it very easy to wire together up to 8 ESCs and 3 addition JST power outlets for FPV and LEDs.   for larger 10kg class Octas  - Plug n Play for our 40Amp ESC HERE which are rated at 1000w x8

 

Hero Features

  • Fully assembled - 4 LiPo INPUT - >  8 Way XT60 output for ESC + 3 x JST 5 amp - as shown with mounting hardware included (see below) - plug-n-play
  • Connects directly to our ESCs in our store - HobbyWing 40Amp ESCs
  • Rated and tested to 60 amps continuous - tested to 72amps for 15 secs - realistically if you are running 6S you should be able to fly at 8Kg and below 60amps ; but I would advise using the 200amp version if close to 60 amps in the hover, mainly so you can run at least 2 LiPos or 4 LiPos not one.
  • tiny product 50x50mm - with standard 45mm hole centres  - (measured square axis across)  - 1.6mm RoHS gold plated PCB
  • Super thick 140um copper rings joined by 192 vias - so both sides of the board act together to conduct large amounts of current - with good air cooling in the layer design.
  • Plated holes for strength and 100% power delivery
  • Additional 3.5mm holes for customisation
  • 8 sets of XT60 connectors for 8 ESC
  • 1 thin wire +ve lead 150mm for ANDROMEDA LED board
  • 4 x M3 mounting holes -  unplated -  to isolate
  • Fits inside the inner deck of all HUNTER 22mm series SCARABS - TriicopterQuadOcta and YSiix or Hexii  
  • 155g complete with all connectors/wires/mounts

Includes

  • 1 x fully assembled 2 layer Voltair® 200Amp layer board - 8 x XT60 (75mm) and also 3 x JST outlets (125mm)  - as per photo - with 4 LiPo inputs (2*75mm and 2*125mm)
  • 4 x 6mm nylon stand-offs
  • 4 x M3 nuts nylon
  • 4 x M3 6mm nylon bolts

 

Excludes/Requires

  • Excludes Deans -> XT60 convertor plug if required
  • Requires insulation from frame - use the supplied  nylon stand offs and nylon bolts and nuts insulation tape after completion - do NOT bolt down directly onto Carbon plates (carbon conducts electricity
  • LiPo batteries are safe if handled correctly - if mis-handled LiPo Batteries will catch fire and burn at 700°C - Dont take risks with cheap chargers or short circuits
    1. Use of a fire resistant bag/container for LiPos - fully Fibreglass lined - not a fake
    2. Use a know/proven top brand charger limited to 4.2v per cell - calibrated - see Gearlist page
    3. Use all balance ports to monitor 4.2v per cell during charge
    4. Use of thermal protection - temp sensor attached on each lipo for cut-off of all power if the charge temp rises about 45°C
    5. Store LiPos at 3.8v per cell

Write your own product review

Product Reviews

  1. Power distribution board

    Posted by Michael on 26th Apr 2016

    I love this board have used it before safes a lot of time being pre soldered , I plug esc bullet connectors straight into xt60 perfect fit , it's a little heavy but you can loose weight by cutting away cables you don't need. I think this is value for money





Currency conversion