Loading... Please wait...
Click the image above to see a larger version
  • mini-Andromeda PDB, ultra bright LED with FPV 5v/12v regulator & FrSky A2
  • mini Andromeda LEDs are bright - do not look directly at these LEDs !
  • mini-Andromeda PDB, ultra bright LED with FPV 5v/12v regulator & FrSky A2
  • mini-Andromeda PDB, ultra bright LED with FPV 5v/12v regulator & FrSky A2
  • andromeda - nearest visible galaxy to earth
  • mini-Andromeda PDB, ultra bright LED with FPV 5v/12v regulator & FrSky A2
  • designed to connect directly to FrSky A2 voltage telemetry input on X4R - note pins
  • example of a Hack to upgrade the 5v system from bec to a uBEC (additional cost item - not included)
  • example of a Hack to upgrade the 5v system from bec to a uBEC (additional cost item - not included)

mini-Andromeda 50 PDB, ultra bright LED with FPV 5v/12v regulator & FrSky A2

$10.95
Shipping Weight:
55.00 Grams
 
 
 
 
Stock Remaining:
24


Product Description

mini-andromeda-pololu-5v-upgrade-8121.jpgThe v3 mini-Andromeda 50 is a multi function CORE PDB made by Carbonbird and includes everything a mini Quad  needs to keep the build clean, compact and reliable - even the LEDs are installed and brighter than anything else on the market for FPV

Features of the mini-Andromeda 50 PDB

  • 8 Ultrabright LEDs (4 Blue front) and (4 x Red Rear) these can be seen at 300m in full Aussie sunlight
  • 12v regulated power for FPV camera/Tx 500ma
  • 5v regulated power for Flight controller 5v / 4.5v 500ma
  • 4s 16.8v input
  • 50 AMP PDB continuous
  • LEDs and PDB consume 1.8w @16v (110ma)
  • Only 17grams with XT60
  • Fits the standard 30.5mm square hole spacing used in all FPV drones 
  • has 8 lead out points to distribute power to 4 x ESC
  • Designed for HS1177 12v PV camera support
  • Designed for 200mw class FPV Tx (350ma nominal power draw via 12v BEC onboard)
  • Nominal power drawn WITH HS1177 camera and 200mwTx combined and LEDs = 5.8w/370ma@16.4v 4s or = 4.1w/360ma@11.6v 3s
  • Nominal power draw without FPV camera or Tx = 1.8w/110ma@16.4v (LEDs only)
  • dimensions 56x38mm (12mm h without xT60)

Includes

  • 1 x mini-Andromeda 50 board  - ready to run on 3S or 4S
  • 1 x XT60 connector
  • 1 x XT30 

Excludes

Andromeda Connection 

 

  • When soldering the XT60 or XT30 connectors be sure to use a LARGE 125w soldering iron so the join can be made in 2 secs - WARNING - using a small 60 or 90w electronics solder tip will take too long and will not be able to create a good joint - a dry solder joint will result in power failure and a crash - RISK - you must use Amtech 223 flux and make solid / rapid soldering joins
  • its is vital NOT to connect other devices to the 5.0v or 4.5v ports - this power is exclusively reserved for the FLIGHT CONTROLLER
  • it is vital NOT to short the base of the PDB onto CARBON ! - Danger - Carbon is fully conductive and shorts of lithium batteries may cause fire /harm /smoke
  • XT60 connectors must be sized (insert a 1.5 tool) so the blades are well spread out - if the XT60 probes are compressed they will not make firm contact with the female on the LiPo battery - lubricate the XT60 with lanolin spray

 

 scarab-knife200-mini-andromeda-x4r-wiring.jpg

 

 


Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!




Currency conversion