Loading... Please wait...
Click the image above to see a larger version
  • The best Charger for Drone batteries USA icharger 106B+
  • iCharger 106B+ LiPo charger for Drone batteries Australia
  • The best Charger for Drone batteries NZ icharger 106B+
  • Best LiPo charger in AU 106B+
  • best RC Hobby Drone LiPo charger  - Australia
  • Image 6
  • how to connect 4 x 106B+ chargers to one larger 1200w power supply
  • XT60 Balance board extrernal for RC

LiPo icharger 106B+ - for Lithium Drone batteries - 10amps

$98.00
Shipping Weight:
990.00 Grams
Stock Remaining:
5


Product Description

 compact DC driven LiPo icharger 106B+ 10Amp - 250w - AU (this unit requires a Power supply when used at home - or a 12v car battery outlet in the field) Top of the line quality item @ a budget price - iCharger brand by Junsi - These a VERY good quality Lithium Polymer charger and balancer unit with full safety features including a battery temp monitoring sensor.  We personally use these in our workshop at Multiwiicopter.com and have done so for 2 years - no issues.  Most importantly they very accurately balance our LiPos ensuring the highest capacity and longest life. 

Specifications

  • Input voltage range required 10.0 - 18.0V DC 
  • Charge current range output 0.05 - 10Amp
  • Discharge current range 0.05 - 7.0A - limited to 20W so for a 4S battery typically at 1amp - to achieve 7amp discharge requires an external load (not included)
  • Maximum charge power capacity 250W @ input voltage > 13.5V
  • Maximum discharge power capacity 20W - works very well but takes a while
  • Maximum extern discharge power capacity 170W @ 20V/7A - needs special instructions and external load (not included)
  • Current drain for balancing
  • Balance accuracy
  • Lithium (LiPo/LiIo/LiFe) battery cell count 1S - 6S series
  • NiCd/NiMH battery cell count 1 - 17 series
  • Pb (lead acid car) battery cell count 1 - 12 series (2 - 24V)
  • Battery setup memories 10
  • Intelligent temperature control Yes
  • PC Connect yes via USB port- requires open source software to log  http://www.logview.info
  • Weight 350g
  • Dimensions (L *W * D) 134*83*25mm 5.28”*3.27”*0.98”
  • User Manual 106B+ HERE

Consider buying 2 or 3 chargers to allow you to charge more packs in a short time attended - your time is valueable.  We have 6 chargers on our work bench. :)

features

  • High power, high current, high-performance power conversion circuits. The iCharger series uses advanced Synchronous buck-boost DC/DC converter technology with an output conversion efficiency that can reach over 90%. This not only saves power and reduces heat build up but also makes the charger more compact.
  • Two input power choices min 10.00v -> max 18.00v  (please note ; Casal power supply output = 18.5v and not compatible): DC jack with auto-resetting fuse (maximum input current 6A) and butt-welded alligator clips with 4mm bullet connectors (25A).The output power can be adjusted to align with the available input power, thus preventing input current overload and protecting the DC source.
  • three types of Lithium batteries - LiPo, Lilo, LiFe - and has a fully integrated cell balancer.
  • Internal temperature sensor and temperature controlled automatic cooling FAN controls the internal temperature and provides intelligent protection. When the internal temperature is over 60℃(140 oF), the output power is automatically reduced by 25%. If the temperature exceeds 65℃(149 oF) the charge cycle is stopped.
  • 10 battery profile memories that can be saved and loaded by number.
  • 2x16 backlit LCD screen that provides rich information including active mode, current, voltage, total charge (mAh), charging time and temperature etc.
  • charging/discharging settings and cycles to meet a wide range of customer needs. For Lithium batteries: balance charging, normal charging, fast charging, storage, discharging, ext-discharging, charge/discharge cycling, and battery monitoring. For NiCd/NiMH batteries: charging-auto, charging-manual, discharging, charge/discharge cycling and forming charge. For Pb batteries: charging and discharging.
  • Lithium battery expanding discharge program. When you connect the external capacity resistance, you can use it as the maximum discharge power capacity—170W (@25V/7A).
  • Lithium battery Monitor program. When you use other equipment to charge or discharge a Lithium pack, you can use the iCharger to monitor the per-cell voltages, battery temperature and process time. If any individual cell appears over-charged or over-discharged or the pack is too hot or the process has gone on for too long, the iCharger will generate an alarm sound and the related information will blink.
  • Electric motor test mode can be used to run-in electric motors, test motor parameters and performance, check tolerances etc.
  • Foam-cut drive. In this mode, the charger acts as a convenient power supply for a hot wire foam cutter.
  • Battery interior resistance measurement. The iCharger can not only measure the internal resistance of the battery pack, and also can measure the per-cell internal resistance (only available for lithium battery).
  • Perfect protection. The iCharger has protection for reversed polarity (input or output), low input voltage, battery temperature, charging capacity and time overrun.
  • upgrade firmware the hardware program by USB port. (must use the siupplied USB cable) The iCharger also support the “Open Source” data of the “logview” software and can display, plot and analyze the charge and discharge data by it. (See detail information about logview in the following website: http://www.logview.info)
  • For those with Fluke meters - experts wanting to calibrate - Calibration can be user adjusted Tech sheet HERE

Includes

  • 1 x 10Amp 6S LiPo charger 106B+ with DC input wires 4mm banana connectors (for P350 power supply HERE) or crocodile clips to auto battery 12v (clips included)
  • 1 x output cable 4mm bullet -> croc clips
  • 1 x Over temp monitor probe cable & sensor
  • 1 x Balance lead 6S -> XH balance board  included - These are vital to protect the charger - if you ever make a mistake and reverse connect the balance leads the inside of the charger will be safe becuase only this cheap part will blow.  Also save the charger pins from wear and tear.  These are now standard inclusions from 14.10.2013
  • 1 x XT60 charge lead included
    • icharger-cables-included.jpg
  • 1 x Special mini USB Cable - this cable is important for Open source software logging or firmware updates in future years
  • 1 x mini CD with .pdf instructions - instructions Full USER Manual 106B+ can also be downloaded HERE 
Excludes/Requires

Application

  • Locate the power supply on a dry flame-proof work bench made from non-conductive insulating material.  Do not use on carpets or car seats or in dusty or wet areas.
  • Connect to an earth leakage protected power supply
  • Once connected please remain in the immediate proximity to ALL charging ops - NEVER walk away from a battery charging station in progress - in the event of any problem the power source switch must be turned off and un-plugged
Carries a 12 months manufacturers repair warranty - Orignal item must be returned at customers expense.  Excludes other than normal safe and careful use.  Excludes tampering (you opened it up), moisture damage, fusion, corrosion damage or modification.
 
 SAFETY 
WARNING! -  these ichargers are the only chargers on the market we actually recommend SAFE -100% - amazing balance charge and cell balancing !!! - This is what happened to a customer who risked using another hobby shop brand of charger without proper LiPo safety monitoring systems in that charger such as accurate cell balance and without thermal cutoff protection and without a fire-proof fibreglass LiPo bag.  Used correctly, attended -  LiPos are safe - used incorrectly they will burn at 700°C. Never buy a charger from a store where they dont ACTUALLY use the product themselves on a daily basis. Other charger will wreck ALL your LiPos from poor firmware and poor balance resistors.
 
WARNING !  NEVER set the wrong battery type - triple check it says LiPo for LiPo battery charging or discharging -  if you set NiCad then attach a Lithium LiPo you will start a big fire if the charge voltage exceed 4.2v !- it will happen if set wrongly!  Check 4.2v is the max and then the 4.2v will flash to show balance draining of that cell whilst lower cells are still charging - Check everything - don't risk your home or family  - even with this charger - so double check the settings are correct - stay in the room and always attach the temp cut off probe as a double safety - we set the cut off temp to 45°C on ours - do the same for your when you set it up!!! 
 
STORAGE - store all LiPo at 3.8v per cell
CHARGING - Always balance charge to 4.2v per cell for LiPo - Charge at 1C = long life . example a 3000mah LiPo -> charge at 3.0amps -
WARNING !  - Charging a LiPo battery above 4.2v per cell can cause a FIRE !  - YOU must stay and monitor the charging process of all LiPo directly and ensure the max voltage of 4.2 is not exceeded.  Read the Lipo battery label carefully.
DISCHARGE - do NOT discharge cells below 3v LiPo 

Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!




Currency conversion