Loading... Please wait...
Click the image above to see a larger version
  • Kakute HolyBro F4 AIO Australia OSD BetaFlight 3.2, AU NZ USA
  • Kakute HolyBro F4 AIO OSD BetaFlight 3.2 USA
  • Kakute HolyBro F4 AIO OSD BetaFlight 3.2 NZ
  • Kakute HolyBro F4 AIO OSD BetaFlight 3.2
  • Kakute HolyBro F4 AIO OSD BetaFlight 3.2

Kakute HolyBro F4 AIO OSD v1.3 with BetaFlight 3.2 AU USA

$37.50
Shipping Weight:
75.00 Grams
Stock Remaining:
9


Product Description

Australia Holybro Kakute F4 AIO All-In-One flight controller runs BetaFlight 3.2 AU  , this FC integrates

  1. F4 flight controller (FC) , BlackBox, Soft mounted IMU,
  2. power distribution board (PDB), and
  3. on-screen display (OSD) in one.

Specs

  • MCU: STM32F405RGT6 32-bit processor 
  • IMU: ICM20689 (SPI) 
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 
  • 3 hardware UARTS (UART1, 3, 6) 
  • 128 Mbit Dataflash chip for Blackbox logging 
  • Dimensions: 35x43x7mm (includes USB in height) 
  • Mounting Holes: Standard 30.5mm square to center of holes  
  • Weight: 7g 
  • FLIGHT MANUAL in English .pdf (by Joshua B) here

The Kakute F4 AIO's layout makes it straight forward to wire up the other components of the drone while keeping the build neat and tidy.  Supports Betaflight (or Cleanflight).    
Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.Soft-mounting built in.
The IMU ("gyro") chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.  
New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.


2 oz. copper PCB allows up to 120A maximum continuous current.Dedicated bootloader button for easy firmware flashing.Low-profile design fits into even very compact frames.
Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on "BAT" pad only).


Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead.Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.Supports BLHeli pass-through for easy ESC upgrade and configuration.


Suitable for Knife 200 and Knife 240 frames

scarab-knife-200.jpg  knife-240.jpg

If you chose the option "full chip erase" when you were reflashing the firmware, which leads to a smart port that can not work properly, please input the following command into the CLI.
#
set sport_halfduplex = OFF
Save


THESE ARE AUG Version 1.3 (fixed) Boards in MWC stock  - There was an issue (interference between the OSD and blackbox) on those older kakueF4 AIOs from some other vendors. HolyBro have managed to fix this bug on the boards shipped since July .  The official Betaflight after V3.1.7 fixed this bug. Those who found there is interference between the OSD and the blackbox on his/her Kakute please reflash the firmware using the hex file offered here
betaflight_3.2.0_KAKUTEF4-0713.hex 

Package Includes
  • Kakute F4 AIO v1.3 FC board *1 
  • spare flex cable IMU*1 
  • spare IMU Foam*3 
  • FREE XT60 connector with leads fitted to XT60 (not attached to PCB)

 

kakute-top-side.jpg

kakute-bottom-side.jpg


Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!




Currency conversion