Loading... Please wait...
Click the image above to see a larger version
  • Futaba R7008SB 2.4GHz Fastest  Dual SBus & SBus2 Receiver AU NZ
  • Futaba R7008SB 2.4GHz Fastest  Dual SBus & SBus2 Receiver
  • Futaba R7008SB 2.4GHz Fastest  Dual SBus & SBus2 Receiver
  • Futaba R7008SB 2.4GHz Fastest  Dual SBus & SBus2 Receiver

Futaba R7008SB 2.4GHz Fastest Dual SBus & SBus2 Receiver

$99.00
Shipping Weight:
139.00 Grams
Stock Remaining:
2


Product Description

The R7008SB is the Perfect Rx for a complex multicopter offering the very latest 7 wire traditional outlets and also SBus and SBus 2 at the same time - you can connect the SBus 2 to your WookM and the SBus(1) to your Zenmuse for example without a hub. This Rx is included with a 14SG radio.  

Includes

1 x R7008SB Rx - Full range with dual short antenna

 

Excludes

Excludes sensors and excludes wires

 

R7008SB Specifications

FASSTest-2.4GHz system(18CH/12CH mode)/S.BUS2 and S.BUS port and 8 channels for conventional system receiver

• Dual antenna diversity • Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)

• Weight: 0.38 oz. (10.9g)

• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)

• Battery F/S Voltage: It sets up with a transmitter

• Extra Voltage port: 0 ~ 70V DC * Be sure that when using ESCs regulated

Link to the transmitter

Easy Link ID allows FASSTest receivers to link to compatible transmitter without pressing the link button on the receiver. 1 Bring the transmitter and the receiver close to each other, within 20 inches (half meter). 2 Turn on the transmitter. Place the transmitter into the receiver linking mode. 3 Turn on the receiver. 4 The receiver will wait for the linking process to begin for 2 seconds. Following that it will return to the normal operation mode. 5 When the LED of the receiver changes from blinking red to solid green, linking is complete. (A link waiting state is ended in 1 second.) • Refer to the transmitters operation manual for complete details on how to place the transmitter into the linking mode. • If there are many FASSTest systems turned on in close proximity, your receiver might have difficulty establishing a link to your transmitter. This is a rare occurrence. However, should another FASSTest transmitter/receiver be linking at the same time, your receiver could link to the wrong transmitter. This is very dangerous if you do not notice this situation. In order to avoid the problem,we strongly recommend you to double check whether your receiver is really under control by your transmitter. • If the System Type of the transmitter is changed, the receiver will need to be relinked to the transmitter.

Channel Modes

The R7008SB is capable of changing its channel allocations as described in the table below. This is especially important when using the receiver in a dual receiver mode. See your transmitter operation manual for complete details on operating in the dual receiver mode. 1 Press and hold down the Link/Mode button on the R7008SB receiver. 2 Turn the receiver on while holding down the Link/Mode button. After power up, the button can be released. 3 The LED should now be blinking red in one of the patterns described by the chart below. 4 Each press of the Mode/Link button advances the receiver to the next mode. 5 When you reach the mode that you wish to operate in, press and hold the Mode/Link button for more than 2 seconds. 6 Once locked into the correct mode the LED will change to a solid color. 7 Please cycle the receiver(s) power off and back on again after changing the Channel Mode.

7008-modes.jpg

FASSTest

FASSTest is a bidirectional communication system between the R7008SB receiver and FASSTest capable transmitters. Multiple optional telemetry sensors may be connected to the S.BUS2 on the receiver and that data is in turn displayed on the transmitter. *Please see your transmitters operation manual to configure transmitter to operate with telemetry sensors.


S.BUS2

S.BUS2 extends S.BUS and supports bidirectional communication. Sensors are connected to the S.BUS2 port. *Only S.Bus2 capable devices may be connected to the S.Bus2 port. Standard S.Bus servos and gyros should not be connected to the S.Bus2 port.


Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!




Currency conversion